Cisco 300-410 Exam Dumps

Cisco 300-410 Sample Question Answers

Cisco 300-410 Sample Questions

Question # 1

A company is expanding business by opening 35 branches over the Internet. A network engineer must configure DMVPN at the branch routers to connect with the hub router and allow NHRP to add spoke routers securely to the multicast NHRP mappings automatically Which configuration meets this requirement at the hub router?

A. Option A
B. Option B
C. Option C
D. Option D 

Answer: C

Show Answer

Question # 2

Refer to the exhibit. The security department recently installed a monitoring device between routers R3 and R5, which a loss of network connectivity for users connected to R5. Troubleshooting revealed that the monitoring device cannot forward multicast packets. The team already updated R5 with the correct configuration. Which configuration must be implemented on R3 to resolve the problem by ensuring R3 as the DR for the R3-R5 segment?

A. Option A
B. Option B
C. Option C
D. Option D 

Answer: C

Show Answer

Question # 3

Refer to the exhibit.While troubleshooting a BGP route reflector configuration, an engineer notices that reflected routes are missing from neighboring routers. Which two BGP configurations are needed to resolve the issue? (Choose two)

A. neighbor 10.1.1.14 route-reflector-client
B. neighbor R2 route-reflector-client
C. neighbor 10.1.1.2 allowas-in
D. neighbor R4 route-reflector-client
E. neighbor 10.1.1.2 route-reflector-client 

Answer: A,E

Show Answer

Question # 4

Refer to the exhibit. A NOC team receives a ticket that data traffic from RA to RF is not forwarded when the link between the RC-RE path goes down. All routers learn loopback IP through the IGP protocol. Which configuration resolves?

A. RD(config)#router bgp B5201RD(config-router)# neighbor 10.10.10.2 update-source loopback 0
B. RD(config-router)# neighbor bgp 65101RB(config-router)# neighbor 10.10.10.3 ebgp-multihop 3
C. RB(config)# router bgp 65101RB(config)#neighbor 10.10.10.3 update-source loopback 0
D. RD(config)# router bgp 65201RDI(config-router)# neighbor 10.10.10.2 ebgp-multihop 3

Answer: B

Show Answer

Question # 5

Refer to the exhibit The remote branch locations have a static neighbor relationship configured to R1 only R1 has successful neighbor relationships with the remote locations of R2 and R3, but the end users cannot communicate with each other. Which configuration resolves the issue’

A. Option A
B. Option B
C. Option C
D. Option D
E. Option E 

Answer: E

Show Answer

Question # 6

Refer to the exhibit.With the partial configuration of a router-on-a-stick. Clients in VLAN 10 on Gi2 cannot obtain IP configuration from the central DHP server is reachable by a successful ping from the route. Which action resolves the issue?

A. Configure the ip/ip/dhcp pool f and network 192.168..210.0.255.255/0 commands.
B. Configure the ip header-address 192-168.265.3 command on the Gi2 10 subinterface. 
C. Configure a valid IP address on the Gi2 interface so that DHCP requests can be forwarded.
D. Configure the Ip dhcp excluded-address 192.168.255.3 command on the Gi1.10 subinterface.

Answer: B

Show Answer

Question # 7

Drag and drop the descriptions from the left onto the corresponding MPLS components on the right.

Answer: .

Show Answer

Question # 8

The network administrator configured CoPP so that all routing protocol traffic toward the router CPU is limited to 1 mbps. All traffic that exceeds this limit must be dropped. The router is running BGP and OSPF Management traffic for Telnet and SSH must be limited to 500kbps.access-list 100 permit tcp any any eq 179access-list 100 permit tcp any any range 22 23access-list 100 permit ospf any any!class-map CM-ROUTINGmatch access-group 100class-map CM-MGMTmatch access-group 100!policy-map PM-COPPclass CM-ROUTINGpolice 1000000 conform-action transmitclass CM-MGMTpolice 500000 conform-action transmit!control-planeservice-policy output PM-COPPNo traffic is filtering through CoPP,which is resulting in high CPU utilization,which configuration resolves the issue ?

A. no access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit ospf any anyaccess-list 101 Permit tcp any any range 22 23!class-map CM-MGMTno match access-group 100match access-group 101
B. control-planeno service-policy output PM-COPPservice-policy input PM-COPP
C. No access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit tcp any any range eq 22access-list 100 permit tcp any any range eq 23access-list 100 permit ospf any any 
D. no access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit ospf any anyaccess-list 101 Permit tcp any any range 22 23!class-map CM-MGMTno match access-group 100match access-group 101!control-planeno service-policy output PM-COPPservice-policy input PM-COPP 

Answer: D

Show Answer

Question # 9

Refer to the exhibit.An administrator is troubleshooting a time synchronization problem for the router time toanother Cisco IOS XE-based device that has recently undergone hardening. Which actionresolves the issue?

A. Allow NTP in the ingress ACL on 10.1.225.40 by permitting UDP destined to port 123.
B. Ensure that he CPE router has a valid route to 10.1.255. 40 for NTP and rectify if not reachable.
C. NTP service is disabled and must be enabled on 10.1.225.40.
D. Allow NTP in the ingress ACL on 10.1.255.40 by permitting TCP destined to port 123. 

Answer: C

Show Answer

Question # 10

Refer to the exhibit.TCP traffic should be reaching host 10.10.10.10/24 via R2. Which action resolves the issue?

A. TCP traffic will reach the destination via R2 without any changes
B. Add a permit 20 statement in the route map to allow TCP traffic
C. Allow TCP in the access list with no changes to the route map
D. Set IP next-hop to 10.10.12.2 under the route-map permit 10 to allow TCP traffic. 

Answer: C

Show Answer