Cisco 350-801 Exam Dumps

Cisco 350-801 Sample Question Answers

Cisco 350-801 Sample Questions

Question # 1

Regarding SIP integrations with Cisco Unified Communications Manager, if the Cisco Unity Connection is configured to listen for incoming IPv4 and IPv6 traffic, how should the addressing mode be set up in the Cisco Unity Connection?

A. Set up is not required. 
B. Set up for each group to use IPv4 and IPv6. 
C. Set up media ports for each port group to use IPv4. 
D. Set up IPv4 and IPv6 in Cisco Unified CM. 

Answer: A

Show Answer

Question # 2

What is the Cisco UCM sizing guidance for deployments of between 5.000 and 10,000 users or devices that use the medium Open Virtual Archive template? 

A. one publisher, two TFTP, and two call processing subscribers 
B. one publisher, two TFTP, and four call processing subscribers 
C. one publisher, one TFTP, and one call processing subscriber 
D. one publisher, one TFTP, and two call processing subscribers 

Answer: B

Show Answer

Question # 3

An engineer with ID0123456789 is designing a new dial plan for a customer that has offices in several countries on four continents around the world. This client also wants to integrate with a Microsoft Lync backend. Which dial plan type does the engineer recommend? 

A. H.323 
B. SIP URI 
C. E.164 
D. TEHO 

Answer: C

Show Answer

Question # 4

What are the QoS requirements for voice and video calls over an a Cisco MPLS VPN?

A. less than or equal to 150 ms of one-way latency 
B. less than or equal to 60 ms jitter 
C. less than or equal to 300 ms of one-way latency 
D. less than or equal to 10 percent packet loss 

Answer: A

Show Answer

Question # 5

Which DSCP service parameter is configured for Cisco TS endpomts and Cisco Communication Manager endpoints? 

A. DSCP for audio portion of video calls 
B. DSCP for audio portion of Cisco Telepresence calls 
C. DSCP for audio calls 
D. DSCP for video calls 

Answer: D

Show Answer

Question # 6

A collaboration engineer configures Global Dial Plan Replication for multiple Cisco UCM clusters. The local cluster acts as the hub cluster, and the remaining clusters act as spoke clusters Which service must the engineer configure on the local cluster’ 

A. Intercluster Lookup Service 
B. Location Conveyance on intercluster SIP trunks 
C. Intra-Cluster Communication Signaling 
D. Mobility Cross Cluster 

Answer: A

Show Answer

Question # 7

What is a function of a System Call Handler in Cisco Unity Connections?

A. Place calls in a queue 
B. Greet callers with recorded prompts. 
C. Filter incoming calls to prevent robocalls. 
D. Identify high-priority calls. 

Answer: B

Show Answer

Question # 8

What is the maximum length of any phone number according to ITU recommendation E.164? 

A. 10 
B. 12 
C. 15 
D. 17

Answer: C

Show Answer

Question # 9

Which command must be defined before an administrator changes the linecode value on an ISDN T1 PRI in slot 0/2 on an IOS-XE gateway? 

A. isdn incoming-voice voice 
B. pri-group timeslots 1-24 
C. card type t1 0 2 
D. voice-port 0/2/0:23 

Answer: C

Show Answer

Question # 10

Location-based call admission control is used in Cisco UCM to control the amount of bandwidth allowed between predefined locations. What must be considered when calculating the number of calls that can be made?

A. A limit of 900 kb is the total amount of bandwidth used for the sum of calls. The use of compression does not impact the amount of calls because only the codec definition is considered when calculating the CAC in Cisco UCM 
B. A limit of 900 kb is the total amount of actual used RTP traffic so the oversubscription can be done for multiple calls adding its maximum RTP stream requirements. 
C. A limit of 900 kb is the total amount of bandwidth used for the sum of the media and signaling in the calls The system allows for an actual of 20% overhead of IP packet headers This is to compare the use of ISDN lines with no IP overhead. 
D. A limit of 900 kb is the total amount of bandwidth used for the sum of calls of the defined codec including headers and media traffic 

Answer: C

Show Answer

Question # 11

An administrator set up Cisco UCM LDAP Directory and already synced the users to Cisco UCM from the Active Directory, but they forgot to set up feature group templates when. doing the import. Which action resolves the issue? 

A. Add another LDAP Directory in Cisco UCM, configure feature group templates, and do a manual sync for that new LDAP Directory. 
B. Use the Bulk Administration Tool to update those users with the feature group template. 
C. Configure feature group templates in the Cisco UCM LDAP Directory and do a manual sync. 
D. Configure feature group templates in the Cisco UCM LDAP Directory and configure the resync interval. 

Answer: B

Show Answer

Question # 12

An administrator is configuring LDAP tor Cisco UCM with Active Directory integration. A customer has requested to use “ipphone” instead of “telephoneNumber” as the phone number attribute. Where does the administrator specify this attribute mapping in Cisco UCM?

A. LDAP Custom Filter 
B. LDAP Directory user fields 
C. LDAP Directory custom user fields 
D. LDAP Authentication 

Answer: B

Show Answer

Question # 13

An engineer implements a new Cisco UCM based telephony system per these requirements. •The local Ethernet bandwidth is sized based on the total bandwidth per call •A G 736 codec is used. •The bit rate is 64 kbps •The codec sample interval is 10 ms •The voice payload size is 160 bytes per 20 ms What should the size of the Ethernet bandwidth be per call? 

A. 31.2 kbps 
B. 38.4 kbps 
C. 55.2 kbps
D. 87.2 kbps 

Answer: D

Show Answer

Question # 14

Which device is a Cisco IP Phone 8800 series phone registered in, if it was registered using Mobile and Remote Access? 

A. Cisco Unified Presence 
B. Cisco Expressway-C. 
C. Cisco Expressway-E 
D. Cisco UCM

Answer: B

Show Answer

Question # 15

What is the major difference between the two possible Cisco lM and Presence highavailability modes?

A. Balanced mode provides user load balancing and user failover in the event of an outage. Active/standby mode provides an always on standbynode in the event of an outage, and it also provides load balancing. 
B. Balanced mode provides user load balancing and user failover only for manually generated failovers. Active/standby mode provides anunconfigured standby node in the event of an outage, but it does not provide load balancing. 
C. Balanced mode provides user load balancing and user failover in the event of an outage. Active/standby mode provides an always on standbynode in the event of an outage, but it does not provide load balancing. 
D. Balanced mode does not provide user load balancing, but it provides user failover in the event of an outage. Active/standby mode provides analways on standby node in the event of an outage, but it does not provide load balancing. 

Answer: C

Show Answer